90 lines
2.9 KiB
C
90 lines
2.9 KiB
C
|
/*
|
|||
|
|
* user.h
|
|||
|
|
*
|
|||
|
|
* Created on: 2023年6月25日
|
|||
|
|
* Author: wyf
|
|||
|
|
*/
|
|||
|
|
|
|||
|
|
#ifndef USER_INC_USER_H_
|
|||
|
|
#define USER_INC_USER_H_
|
|||
|
|
|
|||
|
|
#include "stm32g0xx_hal.h"
|
|||
|
|
#include "main.h"
|
|||
|
|
#include "adc.h"
|
|||
|
|
#include "dma.h"
|
|||
|
|
#include "iwdg.h"
|
|||
|
|
#include "tim.h"
|
|||
|
|
#include "usart.h"
|
|||
|
|
#include "gpio.h"
|
|||
|
|
|
|||
|
|
#include "string.h"
|
|||
|
|
#include "math.h"
|
|||
|
|
#include "stdlib.h"
|
|||
|
|
|
|||
|
|
#include "user_stick.h"
|
|||
|
|
#include "user_iic.h"
|
|||
|
|
#include "AHT20.h"
|
|||
|
|
|
|||
|
|
|
|||
|
|
#define ENABLE_INT() __set_PRIMASK(0) /* 使能全局中断 */
|
|||
|
|
#define DISABLE_INT() __set_PRIMASK(1) /* 禁止全局中断 */
|
|||
|
|
|
|||
|
|
extern DMA_HandleTypeDef hdma_adc;
|
|||
|
|
extern ADC_HandleTypeDef hadc1;
|
|||
|
|
extern TIM_HandleTypeDef htim14;
|
|||
|
|
extern DMA_HandleTypeDef hdma_usart1_rx;
|
|||
|
|
extern DMA_HandleTypeDef hdma_usart1_tx;
|
|||
|
|
extern UART_HandleTypeDef huart1;
|
|||
|
|
|
|||
|
|
|
|||
|
|
//#define FLASHmotor_runtime 0x08007000
|
|||
|
|
#define FLASH485_ADDR 0x08007800 //存放485地址的地址
|
|||
|
|
#define BUFF_LEN 32
|
|||
|
|
#define ADCBUFF_LEN 250
|
|||
|
|
|
|||
|
|
extern volatile uint8_t usart_count; //串口接收数据个数
|
|||
|
|
extern uint8_t RxBuff[BUFF_LEN] ; //串口接收缓冲区
|
|||
|
|
extern uint8_t TXBuff[BUFF_LEN] ; //串口发送缓冲区
|
|||
|
|
extern uint8_t uBuff[BUFF_LEN] ; //用户缓冲区
|
|||
|
|
extern volatile int8_t polarity ,adc_state; //电场极性,投退状态
|
|||
|
|
extern volatile uint8_t electric_flag ; //外加的反向电场极限，0为负，1为正
|
|||
|
|
extern volatile uint8_t motor_state ; //电机状态,1为正常, 0不正常
|
|||
|
|
|
|||
|
|
extern volatile uint16_t RS485ADDR ;
|
|||
|
|
extern uint16_t RegularConvData_Tab[ADCBUFF_LEN] ; //ADC采集原始数据
|
|||
|
|
extern volatile int16_t adc_max; //最终峰峰值和
|
|||
|
|
extern volatile int16_t adc_positive , adc_negative; //加外加电场后的adc值
|
|||
|
|
extern volatile int16_t estimate_value ; //投退判断的差值
|
|||
|
|
extern volatile uint16_t pwm_pulse ; //pwm波脉宽
|
|||
|
|
extern volatile int16_t adcValue_factor; //adc测量值得修正系数*10
|
|||
|
|
extern volatile int16_t adcValue_addnum ; //adc测量值的加减系数
|
|||
|
|
|
|||
|
|
extern volatile int16_t motor_runtime; //电机运行时间
|
|||
|
|
extern volatile uint16_t bad_runtime ; //恶劣环境运行时间
|
|||
|
|
|
|||
|
|
extern uint32_t current_addr; //记录当前电机运行时间的
|
|||
|
|
extern volatile int16_t baud_rate; //波特率；0:9600, 1:19200 2:57600 3: 115200
|
|||
|
|
extern uint8_t tempe ,humidness ; //温度湿度
|
|||
|
|
extern int16_t threshold_value ; //传感器上限阈值，低于300时，认为是退
|
|||
|
|
|
|||
|
|
extern int16_t voltage;
|
|||
|
|
extern int16_t voltage_thresh;
|
|||
|
|
extern int16_t reference ;
|
|||
|
|
extern uint16_t user_temp;
|
|||
|
|
|
|||
|
|
|
|||
|
|
void user_init(void);
|
|||
|
|
void user_main(void);
|
|||
|
|
void ADC_MAX(void);
|
|||
|
|
void Usart_Receive(void);
|
|||
|
|
uint16_t crc16_modbus(uint8_t *data, uint16_t length);
|
|||
|
|
void MODBUS_03H(void);
|
|||
|
|
void send_ack(uint8_t a);
|
|||
|
|
void MODBUS_06H(void);
|
|||
|
|
uint8_t writeflash(void);
|
|||
|
|
uint8_t write_flash(void);
|
|||
|
|
uint8_t write_runtime(void);
|
|||
|
|
void Uart_SetBaud(int16_t baud);
|
|||
|
|
void calculate_voltage(void);
|
|||
|
|
#endif /* USER_INC_USER_H_ */
|