279 lines
9.8 KiB
Plaintext
279 lines
9.8 KiB
Plaintext
#MicroXplorer Configuration settings - do not modify
|
|
ADC1.ClockPrescaler=ADC_CLOCK_ASYNC_DIV4
|
|
ADC1.ContinuousConvMode=ENABLE
|
|
ADC1.IPParameters=master,SelectedChannel,NbrOfConversionFlag,ClockPrescaler,SamplingTimeCommon1,ContinuousConvMode,Sequencer,NbrOfConversion
|
|
ADC1.NbrOfConversion=1
|
|
ADC1.NbrOfConversionFlag=0
|
|
ADC1.SamplingTimeCommon1=ADC_SAMPLETIME_160CYCLES_5
|
|
ADC1.SelectedChannel=ADC_CHANNEL_8
|
|
ADC1.Sequencer=NOT_FULLY_CONFIGURABLE
|
|
ADC1.master=1
|
|
CAD.formats=
|
|
CAD.pinconfig=
|
|
CAD.provider=
|
|
Dma.ADC1.2.Direction=DMA_PERIPH_TO_MEMORY
|
|
Dma.ADC1.2.EventEnable=DISABLE
|
|
Dma.ADC1.2.Instance=DMA1_Channel3
|
|
Dma.ADC1.2.MemDataAlignment=DMA_MDATAALIGN_HALFWORD
|
|
Dma.ADC1.2.MemInc=DMA_MINC_ENABLE
|
|
Dma.ADC1.2.Mode=DMA_CIRCULAR
|
|
Dma.ADC1.2.PeriphDataAlignment=DMA_PDATAALIGN_HALFWORD
|
|
Dma.ADC1.2.PeriphInc=DMA_PINC_DISABLE
|
|
Dma.ADC1.2.Polarity=HAL_DMAMUX_REQ_GEN_RISING
|
|
Dma.ADC1.2.Priority=DMA_PRIORITY_MEDIUM
|
|
Dma.ADC1.2.RequestNumber=1
|
|
Dma.ADC1.2.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,SignalID,Polarity,RequestNumber,SyncSignalID,SyncPolarity,SyncEnable,EventEnable,SyncRequestNumber
|
|
Dma.ADC1.2.SignalID=NONE
|
|
Dma.ADC1.2.SyncEnable=DISABLE
|
|
Dma.ADC1.2.SyncPolarity=HAL_DMAMUX_SYNC_NO_EVENT
|
|
Dma.ADC1.2.SyncRequestNumber=1
|
|
Dma.ADC1.2.SyncSignalID=NONE
|
|
Dma.Request0=USART1_RX
|
|
Dma.Request1=USART1_TX
|
|
Dma.Request2=ADC1
|
|
Dma.RequestsNb=3
|
|
Dma.USART1_RX.0.Direction=DMA_PERIPH_TO_MEMORY
|
|
Dma.USART1_RX.0.EventEnable=DISABLE
|
|
Dma.USART1_RX.0.Instance=DMA1_Channel1
|
|
Dma.USART1_RX.0.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
|
Dma.USART1_RX.0.MemInc=DMA_MINC_ENABLE
|
|
Dma.USART1_RX.0.Mode=DMA_CIRCULAR
|
|
Dma.USART1_RX.0.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
|
Dma.USART1_RX.0.PeriphInc=DMA_PINC_DISABLE
|
|
Dma.USART1_RX.0.Polarity=HAL_DMAMUX_REQ_GEN_RISING
|
|
Dma.USART1_RX.0.Priority=DMA_PRIORITY_MEDIUM
|
|
Dma.USART1_RX.0.RequestNumber=1
|
|
Dma.USART1_RX.0.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,SignalID,Polarity,RequestNumber,SyncSignalID,SyncPolarity,SyncEnable,EventEnable,SyncRequestNumber
|
|
Dma.USART1_RX.0.SignalID=NONE
|
|
Dma.USART1_RX.0.SyncEnable=DISABLE
|
|
Dma.USART1_RX.0.SyncPolarity=HAL_DMAMUX_SYNC_NO_EVENT
|
|
Dma.USART1_RX.0.SyncRequestNumber=1
|
|
Dma.USART1_RX.0.SyncSignalID=NONE
|
|
Dma.USART1_TX.1.Direction=DMA_MEMORY_TO_PERIPH
|
|
Dma.USART1_TX.1.EventEnable=DISABLE
|
|
Dma.USART1_TX.1.Instance=DMA1_Channel2
|
|
Dma.USART1_TX.1.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
|
Dma.USART1_TX.1.MemInc=DMA_MINC_ENABLE
|
|
Dma.USART1_TX.1.Mode=DMA_NORMAL
|
|
Dma.USART1_TX.1.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
|
Dma.USART1_TX.1.PeriphInc=DMA_PINC_DISABLE
|
|
Dma.USART1_TX.1.Polarity=HAL_DMAMUX_REQ_GEN_RISING
|
|
Dma.USART1_TX.1.Priority=DMA_PRIORITY_MEDIUM
|
|
Dma.USART1_TX.1.RequestNumber=1
|
|
Dma.USART1_TX.1.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,SignalID,Polarity,RequestNumber,SyncSignalID,SyncPolarity,SyncEnable,EventEnable,SyncRequestNumber
|
|
Dma.USART1_TX.1.SignalID=NONE
|
|
Dma.USART1_TX.1.SyncEnable=DISABLE
|
|
Dma.USART1_TX.1.SyncPolarity=HAL_DMAMUX_SYNC_NO_EVENT
|
|
Dma.USART1_TX.1.SyncRequestNumber=1
|
|
Dma.USART1_TX.1.SyncSignalID=NONE
|
|
File.Version=6
|
|
GPIO.groupedBy=Group By Peripherals
|
|
KeepUserPlacement=false
|
|
Mcu.CPN=STM32G030F6P6
|
|
Mcu.Family=STM32G0
|
|
Mcu.IP0=ADC1
|
|
Mcu.IP1=DMA
|
|
Mcu.IP2=NVIC
|
|
Mcu.IP3=RCC
|
|
Mcu.IP4=SYS
|
|
Mcu.IP5=TIM17
|
|
Mcu.IP6=USART1
|
|
Mcu.IPNb=7
|
|
Mcu.Name=STM32G030F6Px
|
|
Mcu.Package=TSSOP20
|
|
Mcu.Pin0=PB7
|
|
Mcu.Pin1=PB9
|
|
Mcu.Pin10=PB0
|
|
Mcu.Pin11=PB1
|
|
Mcu.Pin12=PB2
|
|
Mcu.Pin13=PA8
|
|
Mcu.Pin14=PA11 [PA9]
|
|
Mcu.Pin15=PA12 [PA10]
|
|
Mcu.Pin16=PA13
|
|
Mcu.Pin17=PA14-BOOT0
|
|
Mcu.Pin18=PB6
|
|
Mcu.Pin19=VP_SYS_VS_Systick
|
|
Mcu.Pin2=PA0
|
|
Mcu.Pin20=VP_TIM17_VS_ClockSourceINT
|
|
Mcu.Pin3=PA1
|
|
Mcu.Pin4=PA2
|
|
Mcu.Pin5=PA3
|
|
Mcu.Pin6=PA4
|
|
Mcu.Pin7=PA5
|
|
Mcu.Pin8=PA6
|
|
Mcu.Pin9=PA7
|
|
Mcu.PinsNb=21
|
|
Mcu.ThirdPartyNb=0
|
|
Mcu.UserConstants=
|
|
Mcu.UserName=STM32G030F6Px
|
|
MxCube.Version=6.11.0
|
|
MxDb.Version=DB.6.0.110
|
|
NVIC.DMA1_Channel1_IRQn=true\:0\:0\:false\:false\:true\:false\:true\:true
|
|
NVIC.DMA1_Channel2_3_IRQn=true\:0\:0\:false\:false\:true\:false\:true\:true
|
|
NVIC.ForceEnableDMAVector=true
|
|
NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
|
|
NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
|
|
NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
|
|
NVIC.SVC_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:true
|
|
NVIC.SysTick_IRQn=true\:3\:0\:false\:false\:true\:false\:true\:false
|
|
NVIC.USART1_IRQn=true\:2\:0\:true\:false\:true\:true\:true\:true
|
|
PA0.GPIOParameters=GPIO_Speed,PinState,GPIO_Label
|
|
PA0.GPIO_Label=BLED
|
|
PA0.GPIO_Speed=GPIO_SPEED_FREQ_MEDIUM
|
|
PA0.Locked=true
|
|
PA0.PinState=GPIO_PIN_SET
|
|
PA0.Signal=GPIO_Output
|
|
PA1.GPIOParameters=GPIO_Speed,PinState,GPIO_Label
|
|
PA1.GPIO_Label=RLED
|
|
PA1.GPIO_Speed=GPIO_SPEED_FREQ_MEDIUM
|
|
PA1.Locked=true
|
|
PA1.PinState=GPIO_PIN_SET
|
|
PA1.Signal=GPIO_Output
|
|
PA11\ [PA9].GPIOParameters=GPIO_Speed,PinState,GPIO_Label
|
|
PA11\ [PA9].GPIO_Label=TX485_EN
|
|
PA11\ [PA9].GPIO_Speed=GPIO_SPEED_FREQ_MEDIUM
|
|
PA11\ [PA9].Locked=true
|
|
PA11\ [PA9].PinState=GPIO_PIN_RESET
|
|
PA11\ [PA9].Signal=GPIO_Output
|
|
PA12\ [PA10].GPIOParameters=GPIO_Speed,PinState,GPIO_Label
|
|
PA12\ [PA10].GPIO_Label=PWR_EN
|
|
PA12\ [PA10].GPIO_Speed=GPIO_SPEED_FREQ_MEDIUM
|
|
PA12\ [PA10].Locked=true
|
|
PA12\ [PA10].PinState=GPIO_PIN_RESET
|
|
PA12\ [PA10].Signal=GPIO_Output
|
|
PA13.Mode=Serial_Wire
|
|
PA13.Signal=SYS_SWDIO
|
|
PA14-BOOT0.Mode=Serial_Wire
|
|
PA14-BOOT0.Signal=SYS_SWCLK
|
|
PA14-BOOT0__PA15.StandardMode=true
|
|
PA2.GPIOParameters=GPIO_Speed,PinState,GPIO_PuPd,GPIO_Label,GPIO_ModeDefaultOutputPP
|
|
PA2.GPIO_Label=IIC_SCL
|
|
PA2.GPIO_ModeDefaultOutputPP=GPIO_MODE_OUTPUT_OD
|
|
PA2.GPIO_PuPd=GPIO_NOPULL
|
|
PA2.GPIO_Speed=GPIO_SPEED_FREQ_VERY_HIGH
|
|
PA2.Locked=true
|
|
PA2.PinState=GPIO_PIN_SET
|
|
PA2.Signal=GPIO_Output
|
|
PA3.GPIOParameters=GPIO_Speed,PinState,GPIO_PuPd,GPIO_Label,GPIO_ModeDefaultOutputPP
|
|
PA3.GPIO_Label=IIC_SDA
|
|
PA3.GPIO_ModeDefaultOutputPP=GPIO_MODE_OUTPUT_OD
|
|
PA3.GPIO_PuPd=GPIO_NOPULL
|
|
PA3.GPIO_Speed=GPIO_SPEED_FREQ_VERY_HIGH
|
|
PA3.Locked=true
|
|
PA3.PinState=GPIO_PIN_SET
|
|
PA3.Signal=GPIO_Output
|
|
PA4.GPIOParameters=GPIO_Label
|
|
PA4.GPIO_Label=Key_Reset
|
|
PA4.Locked=true
|
|
PA4.Signal=GPIO_Input
|
|
PA5.GPIOParameters=GPIO_Label
|
|
PA5.GPIO_Label=KEY_Down
|
|
PA5.Locked=true
|
|
PA5.Signal=GPIO_Input
|
|
PA6.GPIOParameters=GPIO_Label
|
|
PA6.GPIO_Label=Key_OK
|
|
PA6.Locked=true
|
|
PA6.Signal=GPIO_Input
|
|
PA7.GPIOParameters=GPIO_Label
|
|
PA7.GPIO_Label=Key_UP
|
|
PA7.Locked=true
|
|
PA7.Signal=GPIO_Input
|
|
PA8.Locked=true
|
|
PB0.GPIOParameters=GPIO_Label
|
|
PB0.GPIO_Label=KEY_PWR
|
|
PB0.Locked=true
|
|
PB0.Mode=IN8
|
|
PB0.Signal=ADC1_IN8
|
|
PB0__PB1__PB2__PA8.StandardMode=true
|
|
PB1.Locked=true
|
|
PB2.Locked=true
|
|
PB3__PB4__PB5__PB6.StandardMode=true
|
|
PB6.GPIOParameters=GPIO_Speed
|
|
PB6.GPIO_Speed=GPIO_SPEED_FREQ_MEDIUM
|
|
PB6.Mode=Asynchronous
|
|
PB6.Signal=USART1_TX
|
|
PB7.GPIOParameters=GPIO_Speed
|
|
PB7.GPIO_Speed=GPIO_SPEED_FREQ_MEDIUM
|
|
PB7.Mode=Asynchronous
|
|
PB7.Signal=USART1_RX
|
|
PB7__PB8.StandardMode=true
|
|
PB9.GPIOParameters=GPIO_Speed,GPIO_PuPd
|
|
PB9.GPIO_PuPd=GPIO_PULLDOWN
|
|
PB9.GPIO_Speed=GPIO_SPEED_FREQ_MEDIUM
|
|
PB9.Signal=S_TIM17_CH1
|
|
PC14-OSC32_IN\ (PC14)__PB9.StandardMode=false
|
|
PinOutPanel.RotationAngle=0
|
|
ProjectManager.AskForMigrate=true
|
|
ProjectManager.BackupPrevious=false
|
|
ProjectManager.CompilerOptimize=6
|
|
ProjectManager.ComputerToolchain=false
|
|
ProjectManager.CoupleFile=true
|
|
ProjectManager.CustomerFirmwarePackage=
|
|
ProjectManager.DefaultFWLocation=true
|
|
ProjectManager.DeletePrevious=true
|
|
ProjectManager.DeviceId=STM32G030F6Px
|
|
ProjectManager.FirmwarePackage=STM32Cube FW_G0 V1.6.2
|
|
ProjectManager.FreePins=false
|
|
ProjectManager.HalAssertFull=false
|
|
ProjectManager.HeapSize=0x200
|
|
ProjectManager.KeepUserCode=true
|
|
ProjectManager.LastFirmware=true
|
|
ProjectManager.LibraryCopy=1
|
|
ProjectManager.MainLocation=Core/Src
|
|
ProjectManager.NoMain=false
|
|
ProjectManager.PreviousToolchain=STM32CubeIDE
|
|
ProjectManager.ProjectBuild=false
|
|
ProjectManager.ProjectFileName=revamp_addr.ioc
|
|
ProjectManager.ProjectName=revamp_addr
|
|
ProjectManager.ProjectStructure=
|
|
ProjectManager.RegisterCallBack=
|
|
ProjectManager.StackSize=0x400
|
|
ProjectManager.TargetToolchain=STM32CubeIDE
|
|
ProjectManager.ToolChainLocation=
|
|
ProjectManager.UAScriptAfterPath=
|
|
ProjectManager.UAScriptBeforePath=
|
|
ProjectManager.UnderRoot=true
|
|
ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_DMA_Init-DMA-false-HAL-true,4-MX_USART1_UART_Init-USART1-false-HAL-true,5-MX_TIM17_Init-TIM17-false-HAL-true,6-MX_ADC1_Init-ADC1-false-HAL-true
|
|
RCC.ADCFreq_Value=64000000
|
|
RCC.AHBFreq_Value=64000000
|
|
RCC.APBFreq_Value=64000000
|
|
RCC.APBTimFreq_Value=64000000
|
|
RCC.CortexFreq_Value=64000000
|
|
RCC.EXTERNAL_CLOCK_VALUE=12288000
|
|
RCC.FCLKCortexFreq_Value=64000000
|
|
RCC.FamilyName=M
|
|
RCC.HCLKFreq_Value=64000000
|
|
RCC.HSE_VALUE=8000000
|
|
RCC.HSI_VALUE=16000000
|
|
RCC.I2C1Freq_Value=64000000
|
|
RCC.I2S1Freq_Value=64000000
|
|
RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APBFreq_Value,APBTimFreq_Value,CortexFreq_Value,EXTERNAL_CLOCK_VALUE,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2S1Freq_Value,LSCOPinFreq_Value,LSE_VALUE,LSI_VALUE,MCO1PinFreq_Value,PLLP,PLLPoutputFreq_Value,PLLRCLKFreq_Value,PWRFreq_Value,SYSCLKFreq_VALUE,SYSCLKSource,USART1Freq_Value,VCOInputFreq_Value,VCOOutputFreq_Value
|
|
RCC.LSCOPinFreq_Value=32000
|
|
RCC.LSE_VALUE=32768
|
|
RCC.LSI_VALUE=32000
|
|
RCC.MCO1PinFreq_Value=64000000
|
|
RCC.PLLP=RCC_PLLP_DIV4
|
|
RCC.PLLPoutputFreq_Value=32000000
|
|
RCC.PLLRCLKFreq_Value=64000000
|
|
RCC.PWRFreq_Value=64000000
|
|
RCC.SYSCLKFreq_VALUE=64000000
|
|
RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK
|
|
RCC.USART1Freq_Value=64000000
|
|
RCC.VCOInputFreq_Value=16000000
|
|
RCC.VCOOutputFreq_Value=128000000
|
|
SH.S_TIM17_CH1.0=TIM17_CH1,PWM Generation1 CH1
|
|
SH.S_TIM17_CH1.ConfNb=1
|
|
TIM17.Channel=TIM_CHANNEL_1
|
|
TIM17.IPParameters=Channel,Period,Pulse,Prescaler
|
|
TIM17.Period=1000
|
|
TIM17.Prescaler=64
|
|
TIM17.Pulse=500
|
|
USART1.BaudRate=9600
|
|
USART1.IPParameters=VirtualMode-Asynchronous,BaudRate
|
|
USART1.VirtualMode-Asynchronous=VM_ASYNC
|
|
VP_SYS_VS_Systick.Mode=SysTick
|
|
VP_SYS_VS_Systick.Signal=SYS_VS_Systick
|
|
VP_TIM17_VS_ClockSourceINT.Mode=Enable_Timer
|
|
VP_TIM17_VS_ClockSourceINT.Signal=TIM17_VS_ClockSourceINT
|
|
board=custom
|